wangel
Joined: 16 Apr 2019 Posts: 1 Location: US
|
Posted: Tue Apr 16, 2019 3:43 pm Post subject: miniupnp on pfsense bug? |
|
|
Running PFSense version 2.4.4-Release-P2. I've posted on pfsense's subreddit, but haven't gotten much help/feedback.
I'm sitting miniupnp up for my consoles, a ps4 and xbox one. I'm 99% sure I have it configured it correctly. Below is my current config file:
Code: | ext_ifname=em0
port=2189
listening_ip=em1
ext_ip=111.111.111.111
system_uptime=yes
secure_mode=yes
presentation_url=https://192.168.1.1/
uuid=c83b93ee-af03-59ef-10a2-51d68ba3272
serial=C83B93EE
model_number=1.1
allow 1024-65535 192.168.1.25/32 1024-65535
allow 1024-65535 192.168.1.27/32 1024-65535
allow 1024-65535 192.168.1.28/32 1024-65535
allow 1024-65535 192.168.1.31/32 1024-65535
deny 0-65535 0.0.0.0/0 0-65535
enable_upnp=yes
enable_natpmp=yes
|
Please note that 111.111.111.111 is not my public ip, however I do have my REAL public ip in the config file. I've also tried it without the ext_ip setting.
I can stop the service, restart it ... and it then test the consoles, and they work fine, however after a bit of time, I start seeing this in my log file:
Code: |
Apr 16 03:31:10 miniupnpd 48827 SendNATPMPPublicAddressChangeNotification: sendto(s_udp=10, port=5351): No route to host
Apr 16 03:31:10 miniupnpd 48827 PCPSendUnsolicitedAnnounce() sendto(): No route to host
Apr 16 03:31:10 miniupnpd 48827 PCPSendUnsolicitedAnnounce() IPv6 sendto(): Bad file descriptor
Apr 16 03:31:10 miniupnpd 48827 SendNATPMPPublicAddressChangeNotification: sendto(s_udp=10, port=5351): No route to host
Apr 16 03:31:10 miniupnpd 48827 PCPSendUnsolicitedAnnounce() sendto(): No route to host
Apr 16 03:31:10 miniupnpd 48827 PCPSendUnsolicitedAnnounce() IPv6 sendto(): Bad file descriptor
Apr 16 03:31:10 miniupnpd 48827 SendNATPMPPublicAddressChangeNotification: sendto(s_udp=10, port=5351): No route to host
Apr 16 03:31:10 miniupnpd 48827 PCPSendUnsolicitedAnnounce() sendto(): No route to host
Apr 16 03:31:10 miniupnpd 48827 PCPSendUnsolicitedAnnounce() IPv6 sendto(): Bad file descriptor
Apr 16 03:31:10 miniupnpd 48827 SendNATPMPPublicAddressChangeNotification: sendto(s_udp=10, port=5351): No route to host
Apr 16 03:31:10 miniupnpd 48827 PCPSendUnsolicitedAnnounce() sendto(): No route to host
Apr 16 03:31:10 miniupnpd 48827 PCPSendUnsolicitedAnnounce() IPv6 sendto(): Bad file descriptor
|
This repeats about every 6 seconds ... When this is happening, upnp doesn't work at all .... if I clear the map table and test the consoles, they do not open ports as expected etc.
I suspect this is because my cable modem drops for a few seconds, just enough to weird miniupnp out and it gets stuck in a loop? I'm not sure.
***EDIT***
I have ipv6 turned off in pfsense. My isp doesn't give me an ipv6, so I have the sitting to block ipv6 in pfsense turned ON.... Maybe this is the issue?
"Allow IPV6" All IPv6 traffic will be blocked by the firewall unless this box is checked NOTE: This does not disable any IPv6 features on the firewall, it only blocks traffic.
The box is NOT CHECKED
Any help would be greatly appreciated.
Thank you!
~wangel[/code] |
|